Exactly how to Replace a Tub (Step By Step).
Exactly how to Replace a Tub (Step By Step).
Blog Article
Are you searching for answers about Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't specifically brain surgery, however it does need solid plumbing, woodworking, and also often, tiling skills. Replacing an old bathtub with a brand-new one is also a moderately difficult task. If the old bathtub is easily easily accessible, the job can move easily; if you need to open a wall surface to get rid of the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old tub and also embeded in the new one. Ensure you have certified yourself for the job and also fit trying it. Rather than working with a service provider to take control of a halfway-completed task, it is much better to consider utilizing one prior to you start. Chances are you may require an expert plumber to make tube links.
This write-up will assist you install a brand-new bath tub in your restroom if you have currently bought a brand-new bathtub and also do not require to transform the arrangement of your previous water supply pipes.
Your tools and material checklist should comprise the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to stop stress on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic because of the restricted gain access to that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, position the bathtub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water system and inspect all joints and also brand-new pipework for leaks as well as tighten them if necessary. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, fix the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bath tub should wait until the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in area in between the faucet as well as the sink. Protect the tap in place with the producer provided backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet adapters. The previous type should be connected to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall in between the bathroom and the tiling, bring about problems with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealant can split fairly early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is suggested to fit the ceramic tiles using waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I figured sharing that chunk was smart. Kindly take the opportunity to promote this page if you enjoyed it. Thanks so much for taking the time to read it.
Hire A Pro Report this page